Benefits of picking the right hydraulic fluid

Most mine operators understand the cost-saving potential of effective equipment lubrication.

 

But, looking more closely, it’s clear they don’t understand just how much of an impact it can have on the total cost of ownership, and ultimately, the mine’s bottom line after fuel savings, increased equipment productivity, reduced downtime, lower maintenance costs due to reduced wear and tear on equipment, and improved oil drain and maintenance intervals are all accounted for.

According to an extensive industry survey by Edelman Intelligence, 60% of mining companies believe that cost savings of greater than 5% are possible through proper lubricant selection and management, however, only a quarter think that those savings could exceed 10%. Nearly half don’t believe that choosing a higher-quality lubricant will help reduce maintenance costs. At the same time, nearly all the mining companies surveyed reported unplanned machine shutdowns in the last three years, and more than half acknowledged that these shutdowns have been due to their incorrect selection or management of lubricants.

So where is the disconnect? Choosing the correct hydraulic fluid depends on a combination of the equipment’s design characteristics, operational parameters and environment. Factors like temperature, humidity, dirt and location (altitude/ underground) all pose different challenges for lubrication. OEMs generally define the minimum requirements for lubricants or greases. However, not all products that meet these standards deliver the same level of performance.

With its registered and patented Dynavis technology, the Oil Additives business line of Evonik Industries has been working towards setting a higher industry standard to significantly improve not only the fuel efficiency of mobile mining equipment but also the productivity of the machine. High-quality multigrade hydraulic fluids work by broadening the temperature operating window and delivering more constant viscosity, even under extreme shear stress.

Reliable performance in a wide range of temperatures

By using monograde oils or low-performing multigrade oils there is an increased risk of corrosion and sludge buildup, increased wear and cavitation (air pockets) that lead to faster degradation of the oil, filter-blocking and valve-sticking, and increased oil use, which results in equipment damage, premature failure and replacement of components, loss of operating precision, excessive noise, increased maintenance and expensive downtime.

The key differentiator of high-quality hydraulic fluids to lower-quality oils is improved shear stability and improved performance, especially at lower temperatures, and the ability of the oil to provide improved viscosity control under extreme conditions. This ability to operate in a larger temperature window so that the oil remains thin enough at start-up to circulate quickly enough to protect critical components, and thick enough at temperatures of 90°C to provide the necessary protection to help prevent abrasive wear, is described as viscosity index (VI). While long chain polymers guarantee effective thickening of the hydraulic fluid, short chain polymers provide shear stability, which helps to avoid breaking of the lubrication film.

Dynavis formulated hydraulic oil guarantees an optimal performance in a wider temperature operating range, expressed by the high VI of >180 and a viscosity grade of ISO46.

With an improved VI and increased shear stability, a high-quality multigrade hydraulic fluid enables equipment to work harder (improved productivity), improves machine maneuverability, while extending machine life and oil drain intervals, allowing for less time and money to be spent on maintenance and improving safety on site through reduced man-machine contact.

Increasing productivity while saving fuel

In a comprehensive performance demonstration conducted under extreme heat in a coal mine in Ranchi, India, the application of Dynavis formulated fluid showed promising results with respect to increased overall machine productivity. While trips with the reference fluid measured an average of 10.8 tonnes/litre, Dynavis formulated fluid could move 12.2 tonnes/ litre, an increase in efficiency of 12.4%. In addition, the excavator using the Dynavis formulated hydraulic fluid was more agile and burned less fuel, allowing faster loading of the trucks and shorter trip cycles.

The excavator using the Dynavis formulated hydraulic fluid showed a ratio of 6.7 litre/trip, while the excavator using the reference oil demonstrated an average ratio of 7.4 litre/trip of fuel consumption, an improvement of 10.6%.

Considering that the fuel used for on-site haulage in a mine site operation can exceed 50% of the total energy costs, there is potential for significant financial savings, especially at remote mining sites.

Reducing CO2 emissions becoming a critical cost factor

Burning less fuel also translates into fewer carbon dioxide (CO2) emissions – which is an immediate concern, with carbon taxing being implemented nationwide in Canada by early 2020. Following Alberta’s model, the Canadian government has proposed a floor price for its nationwide carbon tax system at $10/tonne and increasing to $50/tonne by 2022.

Given that a 5,000-tonne open-pit mine consumes around 5,000 litres of diesel fuel per day, and that one litre of burnt diesel emits around 2.7 kg CO2, one open-pit mine can produce 13.5 tonnes of CO2 per day, which adds up to about 4,950 tonnes of CO2 per year.

According to field test results Evonik Industries conducted with a single excavator over a drain interval of 4,000 hours, the machine using a fluid formulated with Dynavis technology uses 3,300 fewer gallons (13,000 fewer litres) of fuel compared to the reference fluid. This translates to 33.3 tonnes of reduced CO2 emissions per drain interval for a single excavator, based on the U.S. EPA’s standard for CO2 production of 10.08 kg/gallon diesel.

Consider what Jim O’Rourke, CEO of Copper Mountain Mining, stated in a recent CIM Magazine article: Copper Mountain’s mine, with 22 trucks and the need for 30 million litres of diesel per year, generates carbon-tax expenses of $2.3 million annually (1.5% of its total budget). These costs are projected to rise to $3.8 million by 2020. Although lubricants obviously won’t solve the carbon conundrum alone, they can play a role in mitigating rising operational costs. The total economic impact is even larger when the additional operating cost savings resulting from the increased productivity are included in the savings calculation.

Cost savings potential exacerbated in extreme climates

Operating a mine in a profitable and safe manner while minimizing waste and CO2 emissions are clear objectives for mine operators. The challenge of accomplishing these objectives can be exacerbated in extreme climates, like in Canada’s Far North, where costs rise due to lack of infrastructure, limited or difficult access to the site, the need to fly-in equipment and personnel over large distances, and harsh weather conditions that increase the demand for power (usually diesel-generated).

Operating costs for a mining project in northern Canada are in fact estimated to be up to 2.5 times higher for base metals than in other mining regions with access to infrastructure. Considering that energy costs can account for 30% of operating expenses in remote regions (in comparison to 10-20% for a mining site in a less remote area), economizing energy and diesel consumption can be a real game changer. Not to mention, machine standstills and equipment failures can incur significantly higher costs for remote mining operations making machine maintenance a key equipment ownership cost.

Considering that one gold mine in California, which is not located in an estimated annual savings of US$1.1 million by switching to a high-performing multigrade fluid in only two 250t Terex excavators, choosing a high-performing hydraulic fluid can play an even more significant role in managing operating costs at remote mine sites. In fact, Shell Lubricants estimates an overall savings potential in the North American mining industry of US$29.1 million by switching to high-performance multigrade fluids.

Good lubrication management can contribute to mining companies positioning themselves to meet stakeholder demands for more environmentally conscious operating procedures and practices.

Switching to a high-performing hydraulic fluid, can help unlock productivity gains and help mining companies reduce overall operating costs.

The author is senior project manager with the Competence Centre for Mining and Mineral Resources, Canadian German Chamber of Industry and Commerce. For more information on Dynavis, see www.DYNAVIS.com.-

---